Quilt Progress: Let The Sewing Begin!

Started sewing the pieces together last night. Grace helped me…

Quilting Progress: Pieces Cut!

The pieces are all cut out and I’ve laid them out to determine how well things work. I think I may make a small replacement to some very dark purple and then otherwise, I’m set to start sewing the pieces together. This will all be machine-made. As you can see below, Hunter was “helping”…

Cutting Quilt Squares

I’ve got about 1200 of 1458 squares carefully cut out. It has been slow going but I wanted to make sure that the squares are spot on. If I was just off by a wee bit, that can turn into a huge difference when you’re working with so many pieces by the time the quilt top is assembled.

Starting A Quilt

I recently picked up Kaffe Fassett’s book, Simple Shapes, Spectacular Quilts and have decided to do the Boston Common quilt…

A Flowered Tote Bag

Last year I’d picked up some fabric so I could make this tote bag. It took me until this year to get around to making it. It’s a pretty simple pattern, but then I forget how slow I can be at sewing things. Glad to have it completed.

Steampunk Costume: Hoop Cage, Part 3

Brenda and I managed to get a lot done on the hoop cage in tonight’s three-hour session. The waistband is complete…

Brenda made the holes for the pop rivets while I finished turning the hoop casings…

Once the hoops were set, we started to pin them to the vertical strips. (Brenda used a pop rivet to close them and the ends were neatly tucked in and sewn together over top.) We managed to get the hoops pinned on. They will need to be adjusted before we permanently attach them with pop rivets and washers. That will be next time.

Steampunk Costume: Hoop Cage, Part 2

Brenda and I found a couple of hours on Saturday morning to continue working on the hoop cage. When I arrived at her place, she’d already taken the time to adjust things so that they hung better, and she marked and numbered everything (vertical strips top edge, strip number, and it has been pinned where the hoop will fit. and marks on the hops for each vertical strip.)

Brenda had a great idea to back the vertical silver grosgrain ribbons with a wider black ribbon…

While she put those together (leaving room for each hoop to slip through) and also covered the waistband, I got to work on the hoop casings. To begin the casings, I needed to join two long pieces of fabric at an angle. If I had just done a seam straight across, this would create a lot of bulk on the inside when I get turned and it could be pretty difficult to pass the hoop through it.

Once the pieces were sewn and pressed, it was time to sew them. The hoops that we have are 5/8″ wide so I needed to make sure that each casing had a bit of extra room.

We noticed that the fabric was fraying a bit so we took the time to serge the edges. This was the first time I’ve had an opportunity to use a serger and after a quick tutorial from Brenda, I was off to the races with it. She was right when she said I’d fall in love with it right away! The edges are so neat & tidy!!

Once that was done, I managed to get one of the casings turned, put the hoop in and pressed it. The next time we meet to work on this, we are hoping to be able to finish this portion of the costume. We have great plans for pop rivets and washers!!

Steampunk Costume: Hoop Cage, Part 1

Brenda and I decided the best way to get started was to start from the outside in. Build the support structure and the bigger pieces and then the details would follow. We started with the waistband. This is sturdy enough to support the skirt. We measured and cut it to size (plus some overlap) and put it on the dress form. From there, we added the following marks:

  • 3.5″ on either side of the front center so that we have 7″ of flat surface across the front of the skirt
  • side points
  • a point between each side point and the 3.5″ marks
  • center back point
  • 2 points equally spaced between each side point and the center back

Once we had the waistband marked, we cut some grosgrain ribbons to hang from each point. The ribbon is sturdy, has a great texture, and is a lovely silvery gray color. We used the measurement from my waist to the bend in my knee plus a couple of inches (to loop it at the bottom). We then taped each ribbon to each waistband point.

Brenda had gathered the green plastic strips that we will use for our hoops from a local company. It’s nice to be able to recycle these. All they needed was a quick wipe with a baby wipe to get the dust off and they were good to go.

We took a guess at the circumference that we wanted for the bottom hoop and marked out some measurements on it so that the vertical ribbons would flow well. We had to make sure that this would hang evenly. It will be important when we make this to make sure that the vertical strips are attached to the hoop. (Imagine if they all slid to one side while you were wearing the costuem or tying to get into it. We’d like to avoid that.)

From here, we attached a couple more hoops, making sure to measure things as we went so that it was all even.

After that I carefully climbed into it so we could get a good look at our start with the hoop cage. we agreed that we’d initially made the bottom hoop too small. We wanted a larger silhouette, so we made a new larger hoop (100″ circumference) and used that one on the bottom and then moved our original 80″ hoop up. When I’d tried it on, we were happy with most of it, although we now saw that our top hoop needs to be larger.The next time we meet to work on this, we will make our top hoop larger and we will add an extra partial loop around the hips (all the way around except along the front 7″.)

We also cut the fabric that will be covering our hoops. we are going to sew casings and enclose the green plastic in them.

Steampunk Costume Fabric

Brenda and I made a trip to Fabricville yesterday where we found some lovely fabrics for our costume. From top to bottom, the fabrics are as follows…

  • The top silver with black striped organza (0.5m of Iowa 53760) is for the airship that will be on top of the top hat.
  • The purple fabric (1m of Stapleton 64740) will be for the corset and will be underneath a black lace.
  • The purple and black fabric (5m of Stapleton 64740) is for the skirt.
  • The pewtery-striped fabric (1m of Liverpool 65040) will be for covering the hoops for the hoop skirt.
  • The grey-green fabric (1m of Velveteen 44525) is for the gauntlets and knee-high spats (and possibly a band on the top hat).
  • We found some great 18 mm buttons (Elan 15 2055 Y) which we will use on the spats and gauntlets.

Steampunk Costume: Mood Board

Brenda & I used inspiring images and gathered some items and materials that we had on hand to get it started…